Skip Navigation

InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)U

unseenkiller

@ unseenkiller @forum.guncadindex.com

Posts
3
Comments
25
Joined
3 mo. ago

  • Giving up on the Franken 9

    Jump

  • Thank you for this. I've got an un-tested file I'm working on - if you're interested in trying it, I'd love your feedback. You can DM me on element about it.

    Otherwise, I'm unhappy about the Franken-9 responses I've been hearing, and will be building one of my own today. Please don't give up, just park it for a day or two while I address this.

  • Giving up on the Franken 9

    Jump

  • yo, show me a pic of your front rail cavity, I think I know what's going on

  • Why is there a dorito in this 2011?

    Jump

  • okay, I want one....

  • Franken 9 Question

    Jump

  • In case anyone is still seeing this post / comment, the Franken-9 frame issue has been identified, fixed, and re-released. The file name is called "Unseenkiller and Corbat67 - Franken 9 - 1-2-2026 Fix.zip", so when you download it, you need to ensure that's what comes down. The post should also be renamed to "Unseenkiller and Corbat67 - Franken 9 (fixed)"

    I've given the fix to Moderator Gage and he should be updating the BLC release file shortly as well.

    Sorry again for any wasted filament or time, folks - this is my bad.

  • Franken 9 Question

    Jump

  • I am not! But that doesn't mean they don't exist.

  • Franken 9 Question

    Jump

  • the one piece I trusted was using good cad, sigh

    yeah i'll hit it hard and it will be fixed ASAP

  • Franken 9 Question

    Jump

  • You're very welcome! Hoping to move this 19 forward sooner rather than later.

  • Franken 9 Question

    Jump

  • I think I recently got a P90 kit, I'm happy to make an R45 v2 if it's being poopy.

  • Franken 9 Question

    Jump

  • The 17 is done and ready. I'm tackling the 19 today. If you're super eager, toss me a DM on element and I'll slide you the 17 as a pre-release.

  • Franken 9 Question

    Jump

  • I had that same issue. I was working off the strength of a room full of beta testers saying they didn't have any issue with the Glock 19 internal geometry so I left it.

    Now that I'm working through my pistol versions of the 19 I'm seeing the same issues. Whatever typo's may or may not exist in the BOM / ReadMe (sorry!), I think if you're not new to Glock, it's not you - it's the design needing a revision to be more inclusive to other parts.

    FWIW, I had the same issue with the 17, and just finished fixing it in the CAD. The 19 is next on my chopping block, and I'm about to throw all of his CAD out and replace it with my tested Block 19 CAD and then start micro-adjusting all the imperfections until I love it.

    So, in summary, my apologies if it's not working for you - there must be some magic "stars aligned" situation going on with the 19 / Franken-9 CAD.

    Notes:

    • try taking out your front or rear rail pin (or maybe both), could be the holes needing to be drilled out
    • try removing your takedown spring, you can't shoot it this way, but you can elevate the takedown with your fingers during install and confirm whether or not there was an issue with takedown pressure (this never happened to me before the Franken-9 assembly)
    • make sure it slides smoothly back and forth without a barrel installed, bad rails, bad friction, bad support junk left in the cavity can angle the rails and make everything bind up like wild (you probably already knew this)

    My "Hammer Fired Glock" handgun series (including 17 and 19) are just around the corner though, so if you're not having luck, you're not at a loss for long.

  • Sling Gang

    Jump

  • cool

  • General Discussion @forum.guncadindex.com
    unseenkiller

    PWC 9L for Lage Max-11S MK2 uppers

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • We haven't really given it a name, we're jokingly calling it The honey dipper sometimes. It will be released in the DLC

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • You can absolutely print a charging handle, but it has to be nylon.

  • 2011 propaganda

    Jump

  • you wouldn't download a car!

  • .45 upper options, vmac... Any others?

    Jump

  • vmac45 is it, there's at least one company I know of currently working on an alternative, though

  • ACR style stock for Cetme C G3

    Jump

  • I like this.

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • i mean, it's right there in the name, sten designs have used the upper hole, the lower reinforcement plate, and the side cutout - there's versions for each design

    the pwc 9 relies on the lower only

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • well? what happened?

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • Wouldn't know! Not super interested in FA or FRT in general, tbh

  • General Discussion @forum.guncadindex.com
    unseenkiller

    PWC - 9mm and 5.7 - Q&A

    (slightly older beta versions in the picture)

    Hey all!

    Because the "PWC: DLC" (DownLoadable Content, for you boomers and non-gamers) will be releasing soon, I figured I'd make a post and open up a general Q&A about the PWC.

    Questions are not limited to the DLC, 9mm, or 5.7 - all questions about the PWC are welcome!

  • General Discussion @forum.guncadindex.com
    unseenkiller

    released a thing

    it's real dumb