Skip Navigation

InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)P

pv2025

@ pv2025 @forum.guncadindex.com

Posts
19
Comments
111
Joined
2 mo. ago

  • 2011maxxin

    Jump

  • i get it... bless!

  • .45 upper options, vmac... Any others?

    Jump

  • wouldnt mac-10 uppers work here ?

  • 2011maxxin

    Jump

  • this mag should work.. since eveything should follow the 2011/1911 'spec'

    Advantage Arms - STI 2011 Wide Body 10 Round Magazine

  • .45 upper options, vmac... Any others?

    Jump

  • 2011maxxin

    Jump

  • 2011maxxin

    Jump

  • Advancedtactical

    there are 1911 kits around 200 on egp. but those look to be unramped 45s.

    for 9mm, ~300, for everything(complete 1911 9mm rampd kit + 2011 parts). seems to be the best deal right now.

  • Don't waste time thinking about which pistol caliber you should build.

    Jump

  • yeah.. only issue is lack of lrho. but outside of that these things rock. im also a HUGE 3011 fan.

  • 2011maxxin

    Jump

  • im guessing this hasnt been published yet.. i dont see it pop on the GCI nor via Odysee search

  • 2011maxxin

    Jump

  • isnt a kit just a 1911 upper + lpk 2011 magcatch and magazine ?

    whats reasonably priced ?

    for a 9mm i suppose the best route is a ria 9mm kit + 2011 parts which puts you around 400. thats without shopping... but yeah at a min it appears a kit would be about 300-400.

    i know youre thinking more along the lines of 150-200(??) if a non-ramped 45, then yeah i suppose one could put together something in that price range. egp.

    respect for all your work..

  • TX22 Pillager Chassis

    Jump

  • is a 100% OEM factory fa needed to complete this build ?

    or can this be built using OEM part "kits" or OEM + SCS parts ?

  • Don't waste time thinking about which pistol caliber you should build.

    Jump

  • ill build them all.. what models are present in this pic ? i have two of these built and love them both. just wish they supported lrho.

    r3 r45

    do all these slide support a side charging handle ? how do you remove the safety to support a side ch ?

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • yeah.. this build project is coming along.. good stuff.. thanks for all your work

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • yeah... i figured that out the other day. thanks for the confirmation though.

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • re: safety tumbler.

    firured out the safety issue. the sear and trigger bar were not correctly installed.

    now need to print another charging handle. i would say plastic charging handles are not it. will have to order a metal ch.

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • seems like the safety is blocking the trigger from fully coming down thuus pushing the sear/trigger block back to disengage/disconnect the hammer. im guessing the tumbler is supposed to roll back to allow the trigger to come down far enough ? what am i missing here ? will the mpa9mm safety selector work ?

    outside of that, the build is complete.. i the meantime i can range test without the safety installed.

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • what afg is this ?

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • whats the difference between:

    RR Feed Lips - Lower Catch

    Printed - Lower Catch

    I loaded each into 15rd varient into the slicer.. both look the same. Also.. which one should be used for the PWC-9 ?

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • Lower Catch Printed

    perfect... i will print out the 15rd magazine labeled..

    Lower Catch Printed

  • PWC - 9mm and 5.7 - Q&A

    Jump

  • just had to clear out material in the bracket slots.. i used a thin enough file to clear out the bracket slots and after that was able to sit the brackets in flush.. now i can run the m4 bolts through each bottom bolt hole pairs.

    now i am cutting the smooth rods to size..

    i took your advice and purchased some extra long smooth rods and just cut them to size as needed.