Skip Navigation

InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)S

StreetSweeper_Arms

@ StreetSweeper_Arms @forum.guncadindex.com

Posts
3
Comments
18
Joined
2 mo. ago

  • VZ 61 Skorpion help

    Jump

  • You will need to dial in your support interface settings and cooling then, also if your bed is too hot or cold it can warp. For PLA+ I usually stick at 55-60c.

  • 5.56 NATO optimized drone shot sabot sailing now.

    Jump

  • I can try this, sick.

  • VZ 61 Skorpion help

    Jump

  • What is it doing? Warping? I also would recommend tree supports, and make sure supports only come from the bed plate not starting on the part either.

  • FTN.5 PA6-CF Annealing Recommended?

    Jump

  • I'll probably try it out since the new flow through can prints way easier for me. Had to use the tight breek because the original one had too much play and caused bore misalignment. So far so good now.

  • FTN.5 PA6-CF Annealing Recommended?

    Jump

  • Yeah lol I never anneal either. Too lazy, my NYLAUG, STG, DB9, and DEAR22 have been fine for awhile.

  • FTN.5 PA6-CF Annealing Recommended?

    Jump

  • I have a question about the FTN.5 and the printed shell, is a 14" barrel safe with the printed shell?

  • PM63 range ready.

    Jump

  • A lot lol

  • PM63 range ready.

    Jump

  • No, it will be in beta soon.

  • PM63 range ready.

    Jump

  • PM63 range ready.

    Jump

  • General Discussion @forum.guncadindex.com
    StreetSweeper_Arms

    PM63 range ready.

    SCS reinforcement rails, minimal fitment, retains use of original stock.

  • PM63 RAK Prototype

    Jump

  • I mean yeah, a new barrel by itself is more than the parts kit typically. Only downside is finding 9x18 makarov, but if you got it with the kit, you could buy a .380 barrel later and have 2 calibers. It's an easy barrel swap, like a handgun.

  • PM63 RAK Prototype

    Jump

  • I got the bowman kit but I am not sure how that one compares.

  • General Discussion @forum.guncadindex.com
    StreetSweeper_Arms

    PM63 RAK Prototype

    Progress on a prototype 63 RAK. Uses SCS rails and barrel locking lugs, all test fits good so far.

  • PM63 RAK Project

    Jump

  • I can get those later but the cuts weren't bad at all just require some dremel work.

  • What should I build? As a first time

    Jump

  • Numrich has good kits if you plan to reweld later, but bowman has good kits with barrel included.

    As far as frames go, ATRH, my remix and there is an AR trigger version I can't remember who makes it though.

  • What should I build? As a first time

    Jump

  • Not really a handgun but skorpion vz61 parts kits are cheap and plentiful and they are super easy builds. One of my favorite guns to this day.

  • PM63 RAK Project

    Jump

  • I really think it will work.

  • PM63 RAK Project

    Jump

  • Honestly I'd just buy one now, cuts on my kit from bowman were really good so it would be an easy re weld either way better to have the kit now.

  • General Discussion @forum.guncadindex.com
    StreetSweeper_Arms

    PM63 RAK Project

    Currently in the testing phase, I may be insane but it might just work. Having the concept for metal plates to be inserted into the frame for the recoil lugs, just finished up the geometry from where Atomic Arms left off.