Skip Navigation

InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)B

BGryph

@ BGryph @forum.guncadindex.com

Posts
0
Comments
4
Joined
9 mo. ago

  • A Fully diy repeater design with 43R

    Jump

  • Last I heard reliable ejection was the barrier.

    The printed cases sometimes require manual removal - whether this can be fixed with thicker walls/smaller loads I don't know.

  • Null 22

    Jump

  • It's not a modifier, it slides up into the channel at the front of the trigger guard and locks the barrel block lock in place.

  • Where can I find screen shots of 300blk nylon settings?

    Jump

  • I took the time to type them all out because I got tired of squinting at screenshots...

    300BLKFDE PA6-CF Settings

    Filament

    Diameter: 1.75mm Flow ratio: 0.98 Enable pressure advance: Yes Pressure advance: 0.032 Density: 1.04 g/cm3 Shrinkage: 100% Price: 40 money/kg Softening temperature: 170 Recommended nozzle temperature: Min 260 | Max 300

    ---Print chamber temperature--- Chamber temperature: 70 Activate temperature control: Yes

    ---Print temperature--- Nozzle: First layer 285 | Other layers 280

    ---Bed temperature--- Engineering plate: First layer 25 | Other Layers 25 Smooth PEI/High Temp Plate: First layer 100 | Other Layers 100 Textured PEI Plate: First layer 45 | Other Layers 45

    Cooling

    ---Cooling for specific layer--- No cooling for the first: 3 layers Full fan speed at layer: 0

    ---Part cooling fan--- Min fan speed threshold: Fan speed 0% | Layer time 5s Max fan speed threshold: Fan speed 0% | Layer time 20s Keep fan always on: No Slow printing down for better layer cooling: Yes Min print speed: 10 mm/s

    Quality

    ---Layer height--- Layer height: 0.15 First layer height: 0.2

    ---Line width--- Default: 0.5 First layer: 0.5 Outer wall: 0.45 Inner wall: 0.5 Top surface: 0.4 Sparse infill: 0.5 Internal solid fill: 0.5 Support: 0.5

    ---Seam--- Seam position: Aligned Staggered inner seams: No Seam gap: 10% Scarf joint seam: None Role base wipe speed: Yes Wipe speed: 80% Wipe on loops: No Wipe before external loop: No

    ---Precision--- Slice gap closing radius: 0.049 Resolution: 0.012 Arc fitting: Yes X-Y hole compensation: 0 X-Y contour compensation: 0 Elephant foot compensation: 0.15 Elephant foot compensation layers: 1 Precise wall: No Convert holes to polyholes: No

    ---Ironing--- Ironing type: No ironing

    ---Wall generator--- Wall generator: Classic

    ---Walls and surfaces--- Walls printing order: Inner/Outer Print infill first: No Wall loop direction: Auto Top surface flow ratio: 1 Bottom surface flow ratio: 1 Only one wall on top surfaces: Yes One wall threshold: 300% Only one wall on first layer: No Avoid crossing walls: No Small area flow compensation: No

    ---Bridging--- Bridge flow ratio: 1 Internal bridge flow ratio: 1 Bridge density: 100 % Thick bridges: No Thick internal bridges: Yes Don't filter out small internal bridges: Disabled Bridgecounterbore holes: None

    ---Overhangs--- Detect overhang walls: Yes Make overhangs printable: No Extra perimeters on overhangs: No Reverse on odd: No

    Strength

    ---Walls--- Wall loops: 6 Alternate extra wall: No Detect thin walls: No

    ---Top/bottom shells--- Top surface pattern: Monotonic li... Top shell layers: 6 Top shell thickness: 1 Bottom surface pattern: Monotonic Bottom shell layers: 6 Bottom shell thickness: 0

    ---Infill--- Sparse infill density: 100 % Sparse infill pattern: Rectilinear Sparse infill anchor length: 400% Maximum length of the infill anchor: 20 Internal solid infill pattern: Monotonic Apply gap fill: Everywhere Filter out tiny gaps: No

    ---Advanced--- Infill/wall overlap: 15 % Infill direction: 45 Bridge infill direction: 0 Minimum sparse infill threshold: 15 Infill combination: No Detect narrow internal solid infill: Yes Ensure vertical shell thickness: All

    Speed

    ---First layer speed--- First layer: 15 mm/s First layer infill: 15 mm/s Initial layer travel speed: 100% Number of slow layers: 0

    ---Other layers speed--- Outer wall: 30 mm/s Inner wall: 30 mm/s Small perimeters: 50% Small perimeters threshold: 0 Sparse infill: 30 mm/s Internal solid infill: 30 mm/s Top surface: 30 mm/s Gap infill: 30 mm/s

    ---Overhang speed--- Slow down for overhangs: Yes Classic mode: No Slow down for curled perimeters: No Overhang speed: 0 (10%, 25%) 15 (25%, 50%) 10 (50%, 75%) 10 (75%, 100%) Bridge: 15 External 150% Internal ---Travel speed--- Travel: 500 mm/s

    ---Acceleration--- Normal printing: 4000 mm/s Outer wall: 2000 mm/s Inner wall: 10000 mm/s Bridge: 50% Sparse infill: 100% Internal Solid infill: 100% First layer: 500 mm/s Top surface: 2000 mm/s Travel: 10000 mm/s

    ---Jerk (XY)--- Default: 0 mm/s Outer wall: 9 mm/s Inner wall: 9 mm/s Infill: 9 mm/s Top surface: 9 mm.s First layer: 9 mm/s Travel: 12 mm/s

    Support

    ---Support--- Enable support: Yes Type: Tree (auto) Style: Default Threshold angle: 30 First layer density: 90 First layer expansion: 2 On build plate only: No Remove small overhangs: Yes

    ---Raft--- Raft Layers: 0

    ---Filament for supports--- Support/raft base: Default Support/raft interface: Default

    ---Advanced--- Top Z distance: 0.19 Bottom Z distance: 0.19 Base pattern: Default Base pattern spacing: 2.5 Pattern angle: 0 Top interface layers: 3 Bottom interface layers: 3 Interface pattern: Default Top interface spacing: 0 Bottom interface spacing: 0 Normal support expansion: 0 Support/object xy distance: 0.35 Don't support bridges: No

    ---Tree supports--- Tip diameter: 0.8 Tree support branch distance: 1 Branch density: 20 Tree support branch diameter: 2 Branch diameter angle: 5 Tree support branch angle: 40 Preferred branch angle: 25 Branch diameter with double walls: 3

    Others

    ---Bed adhesion--- Skirt loops: 0 Skirt distance: 2 Skirt height: 1 layer/s Skirt speed: 50 mm/s Brim type: Outer brim o... Brim width: 25 Brim-object gap: 0.1

    ---Prime tower--- Enable: Yes Width: 35 Prime volume: 45 Brim width: 3

    ---Flush options--- Flush into object's infill: No